Dings happen--and fasteners pop. Maybe that contractor you hired didn't do such a great job of applying the drywall (he didn't press it firmly against the wall when installing the fasteners), or maybe he used cut-rate framing lumber. Never fear. You can repair gouges and popped nails or screws inexpensively yourself.
Instructions
Filling tiny holes
1. Apply a dab of caulk with your fingertip or apply premixed interior spackling compound, available in very small cans, with a putty knife. Fill the hole but don't leave any residue on the surrounding surface.
2. If the compound shrinks as it dries, leaving a dimple, apply another coat. When the compound is dry, touch up the paint.
Repairing a small hole or gouge
3. Place an appropriate quantity of premixed joint compound, available in 1- and 5-gallon (4-l and 19-l) sizes, into a metal bread pan or onto a hawk (see Warning).
4. Pick up a small quantity of compound on the corner of a spackle knife and spread it over the damaged area. Hold the knife on the wall at a low angle and draw it across the compound horizontally; then wipe the knife clean on the edge of the pan and make a second pass vertically.
5. When the first coat dries (it will turn from gray to bright white), apply a second coat, but use more compound and extend it a little beyond the first coat. In the rare case when two coats are not enough, apply a third coat.
6. When the patch is dry, sand lightly and apply primer over the repaired surface before applying a paint topcoat.
Repairing popped fasteners
7. Press firmly against the surface as you drive in one drywall screw on each side of the popped fastener (just above and below it on a wall, or in line with the ceiling joist) with a screwdriver or an electric drill and driver.
8. Drive in the popped fastener tight to the drywall with a hammer or screwdriver. Remove any loose drywall but try not to tear off the paper facing. Apply joint compound and smooth it over as described in "Repairing a small hole or gouge".
Repairing larger damaged areas
9. Apply joint tape wherever the paper facing is badly damaged or missing. To embed paper tape, cover the damaged area with a thin layer of joint compound, press the paper into the compound and smooth it by drawing a clean spackle knife across it with firm pressure. If you're using adhesive-backed fiberglass tape, just press it onto the drywall.
10. When the first coat is dry, scrape off any dry bits on the surface and apply a second and third coat (see A) as described in "Repairing a small hole or gouge".
Patching a large hole
11. Cut a drywall patch. Place it over the damaged area to trace it. Cut along your lines with a drywall saw (see B) or by making repeated passes with a utility knife. Remove the damaged pieces and clean up the cut with a utility knife.
12. Install drywall clips near the four corners of the opening. Slip them over the drywall (narrow spring tabs out) and secure them with 1 1/4-inch (3-cm) Type W drywall screws (see C). Position and screw the patch to the clips (see D).
13. Grasp the clip tabs with long-nose pliers and twist to break them off below the surface. Tape and finish the seams as described in "Repairing larger damaged areas," above.
Related posts
Standard spackling tools professionally repair a small hole in drywall.Drywall is a strong, durable wall covering that creates a smooth finish to the wall. Although the strength and longevity of d...
Anyone with the right tools can make damaged drywall look like new.Removing wallpaper from drywall often results in minor damage to the drywall. It leaves small indentations, exposed gypsum (the c...
Drywall tape stabilizes wet joint compound.When drywall cracks, you can repair the damage and repaint the wall and no one will be the wiser. For the best results, you'll apply semi-solid drywall c...
It's possible to repair outer paper tears and other drywall problems.A material found in residential and commercial structures, drywall is a type of wallboard that contains multiple layers and is...
Repair damaged drywall around a window.Drywall panels, made from tightly compressed gypsum particles and covered with thick paper, offer a smooth interior wall surface. Unfortunately, drywall is r...
